How to Add E-Liquid to Your Device

Standard Atomiser Tanks
Standard Atomisers use coils with a resistance of 1 Ohm or above. These are paired with lower powered devices such as Starter Kits or Vape Pens. Standard Atomiser Tanks are filled from the bottom, meaning you need to unscrew the Tank from the Battery to add the E-Liquid. Please follow the below steps for detailed information on how this is done:

  1. Hold the Tank in one hand and the Battery in the other.
  2. Turn the Tank anti-clockwise and the Battery clockwise until the two parts seperate.
  3. Place the battery to one side and turn the Tank upside down.
  4. Open your E-Liquid and place the nozzle of the bottle into the hole underneath the Tank.
  5. Squeeze the E-Liquid bottle until the Tank is almost full.
  6. Carefully screw the Battery back on to the Tank.
  7. Leave your Vape to sit for 5/10 minutes in order for the cotton to become saturated with E-Liquid.

Sub Ohm Tanks
Sub Ohm Tanks use coils with a resistance of less than 1 Ohm. These are paired with high powered Mods which usually hold 2 high powered batteries. Sub Ohm Tanks are filled from the top by sliding the top section of the Tank to the side to reveal a filling hole. For full information on how to Fill your Sub Ohm Tank please follow the below steps:

  1. Hold your Mod in one hand and grip the top of the Tank (where the Drip Tip is).
  2. Twist the very top of the Tank anti-clockwise to reveal the filling hole.
  3. Open your E-Liquid and place the nozzle of the bottle into the filling hole.
  4. Squeeze the E-Liquid bottle until the Tank is almost full, taking care not to get any in the central airflow chamber.
  5. Twist the top of the Tank back into place until it clicks shut.
  6. Leave your Vape to sit for 5/10 minutes in order for the cotton to become saturated with E-Liquid.

Replaceable PODs
POD Kits use an ingenious system of Replaceable PODs. Each POD will be made specifically for the POD Kit it came with, you can only use the PODs specific to your kit. Filling PODs is really simple, you just take the POD out of the device and lift the small rubber flap which covers the filling hole. Once filled, simply place back in the POD Kit and you're ready to vape. For full instructions, please follow the below steps:

  1. If you have a POD Kit with a 'clip-in' POD, simply hold the bottom of the POD Kit in one hand and pull the POD itself out with the other hand.
  2. If you have a POD Kit with a 'latch' system, simply press or slide the release button on the side of the POD Kit to release the POD.
  3. Place the POD Kit to one side and turn the replaceable POD upside down.
  4. You should notice a small piece of rubber. Pull the rubber cover up to reveal the filling hole.
  5. Open your E-Liquid and place the nozzle of the bottle into the filling hole.
  6. Replace the rubber cover on the replaceable POD, making sure to re-insert the nib in order to seal the POD.
  7. Push the replaceable POD back in to your POD Kit until you hear/feel it click.
  8. Vape straight away without any need to wait for the cotton to saturate.

Rebuildable Dripper Atomisers (RDAs)
Rebuildable Dripper Atomisers (RDAs) require you to build your own Coils and add your own wicking material (cotton) to the Coils to make what's known as a 'Build'. Unlike conventional Atomisers or Tanks, RDAs work by simply dripping a few drops of E-Liquid directly onto your Build then vaping until the Coil is dry and adding more E-Liquid. As RDAs are quite complicated you need to know a lot more than how to add your E-Liquid in order to use them properly. For full information on Rebuildable Gear, visit our blog A Guide to Rebuildable Vaping.